0 Read Quick Guide and User Manual first for quick tips that make using your AITech product more enjoyable. ProA/V Media Extender Wireless HDMI AIT
9 C. Remote Controller Unit (RCU) Instruction Note : 1. Press Power key to transmitter, transmitter will ent
10D. On Screen Display (OSD) vs. RCU Instruction Press the POWER button (1) Press the power button on the RCU to Transmitter or press the
11 ▃▆█▃▆█▃▆█▃▆█ HDMI1 [CH10] WIDE Off 1280x1024 Press again to change Channel Press the “Channel” button again within 5 seconds to switch Ch
123. Installation Step1: Setup the TRANSMITTER Connect Two High-Definition Audio/Video Sources and an HDTV to the TRANSMITTER:
13Step2: Setup the RECEIVER HDTV set Connection with RECEIVER: (1) Connect the HDMI cable to the HDMI OUT jack of the RECEIVER and to you
14Step3: Setup the IR blaster extender cable and IR sensor extender cable If necessary, connect the Infrared (IR) blaster (or sensor) Extender cab
15 (2) If your connected device will be out of the direct line of sight of your remote controls, plug the IR Sensor Extender cable into the I
16Step 4: Boot up the TRANSMITTER and RECEIVER (1) Place the two AAA batteries into the remote control. (2) After
17 (4) If it is in Standby mode and Loop-thru. display on (Transmitter POWER LED is lit in purple and Receiver POWER LED is lit in red), pr
18 (6) Press the Source button, until you see the video being broadcasted from your device. (7) If you have electronic devices such
1 Table of Contents TABLE OF CONTENTS ...
19B. Channel Number Indicating the Wireless Frequency : US ( DFS ) Europe ( DFS ) Japan ( DFS ) WIDE mode Off Frequency [MHz] Support Region Ch
20(8) If all operation is normal, the POWER LED and SOURCE LED will glow in solid blue. Please refer to the next form containing detailed LED desc
21 Note: A. If there is no signal quality shown, and the Source & Status LED is blinking in blue, the transmitter is most likely out of rang
22Step 5: For multi-room audio/video transmission or transmission between different floors, user could press the “WIDE” button on the remote con
23Step 6: Mounting to the Wall (1) Refer the drawing of the bottom page that have relative position of the key holes and attach this paper on
244. Troubleshooting Problem Solution The ProA/V Media Extender Wireless HDMI front panel power indicator (red LED) doesn't light up. • Che
25No audio. • Check your TV’s volume is properly set and not in "MUTE" mode. • Check if the audio connectors are properly connected. •
265. Supported Resolution If the SOURCE LED continues to blink in blue (slower than “no signal” mode); OSD display: “No Supported Format ” and the
276. Audio Bit Rate Support Digital Audio from HDMI inputs: Up to 6Mbit/s bit-rate support. Support AC3 and DTS. 2-channel PCM over S
287. Product Specification General Specifications Supported Video Resolutions HDMI Input 1080p, 1080i, 720p, 576p, 480p Supported Audio Formats
2 1. Important Information Please take the time to read this user manual before using the TRANSMITTER and RECEIVER. It contains important info
29
3 Special Notice Never use this product nearby an aircraft or medical facility.
4 CAUTION of RF module on US region Any changes or modifications not expressly approved by the grantee of this device could void the user&apo
5 CAUTION of System on US region Any changes or modifications not expressly approved by the grantee of this device could void the user's a
6 2. Introduction ProA/V Media Extender Wireless HDMI audio/video transmission solution allows users to place their HDTV set or projector where yo
7 2.2 Overview A. TRANSMITTER: Full HD Transmitter Front Panel Buttons and LEDs Power Button with LED Indicator Press to turn the transm
8 B. RECEIVER: Full HD Receiver Front Panel Buttons and LEDs Power Button with LED indicator Press to turn the receiver on and off.
Kommentare zu diesen Handbüchern